Sep 28 2015

AADL Fairy Housing

The fairy house at the Ann Arbor District Library has unfortunately suffered some structural issues, and as we all really want the fairies to stick around, I have begun building a new abode.  The first step was to take a trip to the always amazing King Books in Detroit.  As you can see, after wandering the aisles of their children’s books I was able to put together a wonderful collection of books to use.

fairylibraryhouse

 

In order to prevent the same type of damage as happened to the original, I am constructing a wooden box to be used as the primary structure rather than simply using the books themselves.  The back panel will be removable to make repairs or additions possible, and I have run copper tape wiring throughout, with tiny outlets to be able to have table lamps and overhead lighting to read and work by.

fairylibrarystructure

The floors were laid one plank at a time with thin strips of maple wood which will then be stained and varnished.  I plan to use dollhouse beadboard for the lower part of the walls, and illustrations from the books as wallpaper.  The windows holes are cut, and trim will be added later.  The early stages and planning are going well, but there is a lot more work to do!  Before I go any further, however, the whole home will be taken in the library to make sure that the existing door will line up with the new room.

 

 


Mar 3 2014

Small change, big impact

Here’s an example of how a fresh coat of paint can really change the feel of a piece.  It was a super fast project, even faster since it’s miniature

IMG_4588IMG_4593

IMG_4594

 

I find it easier to remove the hardware before painting and then reinstall rather than trying to avoid painting on them.  A light sanding followed by several coats of black paint created the base, and using sandpaper or an exacto blade, you can lightly distress all of the edges until you get the look you want.  Finish it off with a coat or two of polyurethane, and done!


Mar 3 2014

Miniature Wall Sconce

 

IMG_4562

The dollhouse has been rewired using copper tape, and miniature scale outlets.  For most of the lighting I have done so far, this has been sufficient, however, in the hallway I did not want a cord hanging down the wall, and so decided to hardwire the fixture in.  I learned how to solder in order to install the overhead kitchen light,  but did not want to use that method, as it seemed that it would be much more difficult to do on a vertical surface.

Begin by determining the location of your sconce.  Drill a small hole, and run a vertical run of copper tape on the opposite side of the wall, just next to this hole.

Once the copper tape is in place, the next step was to create the sconce itself.  To recreate this you will need:

-a”candle” style bulb with wire attached (found in dollhouse stores)

-two short lengths of aluminum pipe (found in craft or hardware stores, they come in lengths of 2-3′, and varying diameters)

-watch gear or similar object to cap the pipe

-bead cap

To make the sconce, cut the two pieces of aluminum pipe to length.  Near the base of one of the pipes gently drill a hole using a dremel tool.  The trick is to drill the hole without squashing the pipe, as the aluminum is soft.  Line up the horizontal pipe with the hole in the vertical pipe and glue in place.  Next, insert the bulb through the vertical pipe and guide the wire through the horizontal, with plenty extra for wiring.  Glue the watch gear on the base of the vertical pipe to create a finished edge, and insert the horizontal pipe into the beadcap.

Once you know how much wire you need to reach your copper tape, cut to length.  Separate the two wires, and gently strip the insulation.  When stripping the insulation, expose a short length of wire before removing completely, and twist gently to keep the copper strands from separating.  Once the wire is exposed, use two of the brass tacks used installing the copper tape, and wrap each wire around a tack 3 times or so.  Guide the wires/tacks througth the hole in the wall and glue or putty the fixture in place.  The tacks can then be hammered into each run of the copper tape.  This should be sufficient to maintain the circuit.  Make sure not to cross the wires, or allow exposed wire to touch more than one strip.  To keep the wiring in place, adjust as needed and then use electrical tape to secure.

Voila!  You have a functioning wall sconce!

IMG_4561

 

 


Feb 28 2014

Miniature Baskets

The dollhouse library is complete, save filling the shelves.  I’ve had a pretty good start when it comes to books and magazines, but what the bottom shelves really needed were baskets.  Inspired by the IKEA cube baskets I use everywhere in my own home, I set out in search of something similar.  Unfortunately, or fortunately, depending on how you look at it, I haven’t been particularly successful in my search.  There are a lot of miniature baskets on the market, but none of the style and size I was searching for.  The solution was obvious- I needed to make my own.  I thought briefly of learning to weave baskets, but since I have no experience at weaving, but quite a bit of experience at crochet, I decided on the latter.

The baskets are crocheted using the tiniest hook I could find, and bamboo and/or hemp cord found in the jewelry department of most big craft stores.  The first several baskets I made were cubes, crocheted and then lined on the inside with bristol board cut to size and wrapped in muslin scraps.  Alternatively you could leave them unlined and use starch to stiffen them, but I really like the added finish of the lining, and it helps to disguise any loose threads left on the interior of the basket.

IMG_4559

IMG_4597

 

The first few baskets I created are shown in the photo above.  After making several cube baskets, I decided to improvise some others as well.  The blue basket below was crocheted in the same manner as the others, but was done using colored raffia.  It requires much more weaving in of the ends, as each strand of raffia would only make it around the basket once or twice, and hooking the material is slightly more tricky as it isn’t consistent the way thread or cording is.  The results, though, are pretty wonderful.  There is a lot of depth in the color, and the finished texture feels just like you’d expect a raffia basket to feel.  The raffia is also much more stiff when crocheted tightly, and didn’t require any extra lining to keep its shape.  The white lining in this case is simply muslin fabric, again, helping to hide all the loose ends and giving the interior a nicely finished feel.

IMG_4608

 

My final basket “experiment” I decided to create one much smaller (equivalent to roughly 6″ in real life) with a lid.  The basket was crocheted in the round, and the lid is simply one round bigger than the base.

IMG_4589IMG_4617

 

 

For those interested, here is a general pattern to follow for the square baskets:

ch – chain stitch   sc- single crochet   blo- back loops only

You may need to play with the size of thread used, as I have a tendency to crochet very tightly.

-Begin with single chain stitch

-8sc in ch, pull tail to tighten loop,  ss in first sc

-ch 1, [sc, 3sc in next sc]x4, ss in first sc of row =16st

-ch 1, [2sc, 3sc in next sc]x4, ss in first sc of row = 24st

-ch 1, 24 blo sc around, ss in first blo sc =24 st

-ch 1, 24 sc around, ss in first sc = 24 st

-Continue sc around for as many rows are you’d like your basket to be tall.  For a cube basket, this would be 8 rows tall including the first blo row.

-To finish, ss across top row, or leave long tail and stitch through each sc for a finish detail.  Weave in all ends.

Variations for addtional detail- try a row of sc in front loops only for a raised detail, or work in a new color at any point to add stripes or a band along the top.

 

If you have any questions, don’t hesitate t ask.  I’d love to see what other people come up with as well!

 

 


Oct 4 2013

Miniature Reading Nook

IMG_4027

 

The dollhouse reading nook is nearly finished, just waiting on its crown moulding and baseboards.  The window seat has a nice padded cushion and throw pillows, and the shelves are being filled with wonderful tiny books.  The pillows and cushion were sewn by hand; tiny beads were used to add tufting details to the seat, and contrast stitching added  detail along the edge of the red pillows.

IMG_4028IMG_4030

 

The window covering was also created by hand.  It was relatively simple to make, but is stationary (I’m going to try making functional roman shades in another room).  I cut a piece of grass paper to the width of the window opening, gave it an accordion fold, and then used thread to hold it in place.  Starting from the base of the shade, simply thread a needle, knot the end,  and draw it through the layers, making sure to end on the back side of the shade.  Once both sides are threaded you can play with it until they are hanging evenly, and then glue in place.  To install the shade, I cut a piece of balsa to  the width of the window opening, glued the shade to it, and then glued the whole thing in place.

This room is particularly special to me, as at least four women in my family have made the miniatures within it.  My grams, Irene Moon,  made the main furniture and inspired most of my choices in decor, my aunt, Alona Moon, created the stone fireplace on the far wall, and my great aunt, Oma Holbrook, painted the watercolors now framed on the wall over the stairs.  Not to sound overly sentimental, but having these small pieces reminds me every day of the amazing family I came from.

 


Oct 1 2013

Miniature Library

 

This room was in need of stripping, and redoing the electrical as with the rest of the house.  Most of this work was done by my sister before the dollhouse came to me.  I added outlets along the walls, and wired the lights on the ceiling of the kitchen below.

gutted playroom

The colors and feel of the room were based around two things; the stone fireplace created by my aunt circa 1988, and the burgundy furniture my grams built from kits.  The floors are cherry planks laid one at a time.  The beadboard panels were fit to the wall and window, and everything painted white.  The deep blue “wallpaper” is a lightweight cardstock I had amongst my stash.

IMG_3348

With the stairs facing the opposite way as my gramps had installed them, it creates a bit of a nook near the back window.  It seemed in need of a window seat and library.  Built in bookshelves line both side walls of the nook.  They and the window seat are made to a 1/12″ scale depth.  The seat lid lifts off to reveal storage inside.  I’m planning to add shelving above the window for display, and cap the entire built in with crown moulding.

IMG_3344

The books on the top shelves in the nook were part of the original dollhouse, and the other are mostly from shops on etsy.  Be warned that the miniature book selection is pretty awesome, and only search with the full understanding that you may become completely oblivious to time.

Obviously the nook needs a softer spot to read,  so cushions, pillows, and a window covering are up next!

 

 


Sep 13 2013

Unnecessary Detail

IMG_3984

Once the bed is made, the mattress doesn’t show.  So why make it detailed?  Well, because unnecessary level of detail is my specialty of course!  Seeing several beautifully done mattresses on Etsy, I was was inspired.

IMG_3973

For this project you will need:

  • foam piece cut to fit your bedframe
  • white muslin or other fabric as the mattress cover
  • scissors
  • fabric glue
  • needle & thread
  • five small buttons or beads for tufting.

IMG_3975IMG_3977

 

To begin, wrap the foam with fabric as you would gift wrap a box.  There’s not any one “right” method for this.  Use a small amount of fabric glue to help keep the fabric in place, but avoid putting glue on the edges, as it will make the edge stitching much more difficult.

Once the top and sides of the mattress are wrapped, it is time to add the tufting details.  To do this, simply thread your needle and push it through the bottom (uncovered at this point) of the mattress.  Reference the finished photo to see the placement of the tufts.  Thread a small bead or button onto the thread, and pass the needle back through to the backside of the mattress again, pulling just enough to create a small tufting effect.  Repeat for each of the tufts; 5 is a good number for a twin bed.

After the tufting looks as you want it to, cut a small rectangle of fabric to cover over the bottom of the mattress.  In the photo above you can see that I folded and glued the edges of the bottom piece so as to not have any unfinished edges.  Glue in place.

Lastly, stitch along each edge of the mattress, creating the illusion of trim.  Again, there’s not really one “right” way to do it.  I found that by pinching the edge gently and stitching perpendicular to the edge I created the look I was going for.

And that’s it!  A realistic looking mattress ready to be fitted with sheets and blankets.  This way, even on “laundry day” your dollhouse mattress will look wonderful!

IMG_3983


Sep 12 2013

Modern Miniature Chair

IMG_3986

I’ve found it is rather difficult to find modern affordable dollhouse furniture, so I decided to try my hand at making my own.  The chair is a relatively simple construction, using wood scraps, a small amount of polyfill, scrap leather, aluminum tubing for the legs, findings or other material to cap the bottom of the legs, wood glue, and fabric adhesive.  The only other tools needed are a cutting mat, exacto knife, scissors, and ruler.

IMG_3274

IMG_3275

I did not use any particular pattern in creating the chair, but googled for some  basic standard chair dimensions (namely seat height and width).  The body of the chair was cut from basswood.  The arms and back were simply wrapped in leather and glued in place.  The seat cushion was first covered in a layer of polyfill, then wrapped in leather, and a small tube of leather was stuffed to serve as a back cushion.  Once the leather part of the chair was finished, the entire thing was set atop a wood base painted silver and four short aluminum tubes were added as legs.  The bottom of the tubes should be fitted with a cap of some sort to make it look more finished, and to keep the aluminum from scratching your wooden dollhouse floors.  I used earring stud “findings” for this purpose.

This was a pretty straightforward and simple furniture project.  With almost the entire chair covered in leather, there was no need for exact carpentry skills, and with legs attached last the height of the seat can be easily altered if needs be.  All in all, it fits pretty nicely in a modern dollhouse living room!

IMG_3985

 

 

 


Sep 12 2013

Kitchen Reno Part 2

The decorating of my dollhouse kitchen is in homage to “grandma’s” kitchens, literally.  The wallpaper was chosen to match the kitchen of my grandmother, mother, and aunts.  The ceiling of the kitchen is designed in homage to the kitchen my mother-in-law had for over 30 years.  The beams are doing double duty, as there was a large crack in the floor above, and not only did they mimic the ceiling I was replicating, they worked perfectly to reinforce it without having to figure out a way to cut out and replace the old subfloor.

IMG_3332

I decided to try my hand at making tiny curtains for the window, and it’s really not difficult if you have a little bit of sewing experience, some wire, and eyelets used in scrapbooking.

IMG_3990

To create the fabric panels, simply cut two equal sized rectangles, adding extra size for the hem.  ”Fat quarters” used in quilting are an easy way to buy a small amount of fabric for this.  The size of the finished panels should be determined by the size of your window, and how long you wish them to be.  First I hemmed all four edges, turning it twice before stitching so as to have a clean finished edge on both sides.  Along the top edge of the panels I installed eyelets you can find in scrapbooking supplies.  I used 5 eyelets per panel, but again, adjust according to the size and look you want.  If you do not have eyelets, you can always simply turn over the top edge again, leaving room for the curtain rod to slide through.

The curtain rod is a wooden dowel, painted, and capped with tiny polymer clay finials.  Beads would work just as well.  Glue one finial in place, slide your curtains onto the rod, and then add the second finial.  The finials can be anything, but it’s helpful if they are large enough that the curtains can’t slide off.

Next, I used black “fun wire” to create the curtain rod hangers and tie backs.  Below is a photo of the wire “hardware”.  To attach the hardware I simply used glue, but you could alternatively use tiny brads or nails.  Once the glue is dry, simply hang the rod with curtains already installed on the hooks and gently position the panels in the tie-backs.

IMG_3988

Next up, the flooring.  I used small glass tiles in black and white, found at a craft store in their mosaic supplies.  One tip, measure the floor ahead of time to determine how many full tiles will fit and whether the space left will require cutting tiles.  The remaining space was small enough that I was able to avoid any tile cutting by leaving a small space on each border that can be covered once the baseboard and quarter round trim is installed.  This saved a lot of time and headache.

IMG_3995

Next up for the kitchen, finishing the tile floor, installing the baseboard and quarter-round trim, and installing the new and improved staircase.


Sep 9 2013

Kitchen Renovations

Thankfully dollhouse renovations are a bit simpler than functional kitchens… no water to shut off, no concerns about gas lines or where to cook in the meantime.  And good thing too, as this reno is taking much longer than expected.  It began with the repurposing of furniture my grandmother had built and finished from kits in the 80s.  First the pieces were sanded, primed, and painted white.  In order to update the pieces I added simple legs, and replaced the top with a “butcher block” counter created by laying strips of wood in varying colors side by side, gluing them in place, cutting them to fit, adding a simple miter cut edge, and then varnish to seal.  You can see the almost finished kichen cupboards below.

IMG_3006

IMG_3012

 

In addition to the cupboards, the sink unit was also updated to match.  The sink was created from polymer clay, and both the faucet and towel rod on the side were made of aluminum tubing (you can find at most hardware stores).  In order to allow the faucet to swivel between the two sink halves first insert and glue a small piece of tubing into the cabinet, and then use the next smallest size of tubing for the fixture.  Aluminum tubing is extremely easy to bend with hand tools.  I recommend using rounded pliers in order to keep the aluminum from creasing.  Simply slip the faucet into the fixed tubing and it will move freely.  The towel bar on the side of the cabinet is also made from aluminum tubing, capped at each end with an earring finding, and hung from simple brackets made of wire.

Next up, the room itself (the beginning of which can be seen in the photo above).